*#0606# shows you Secret Code, but only without SIM Card.

*#06# for checking the IMEI (International Mobile Equipment Identity)

*#002# to kill divert

Resets language to automatic selection : * # 0000 # then Green button

Pin Out (electrical connections)

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO

SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

Tetris
Power on phone and enter PIN. before phone has locked onto network, F9, send own number, hit right button, hit 9. left is 2, right is 8, rotate is 5, and drop is 4.

Monitor Mode
1. Menu
2. 9 (Phone Options)
3. 7 (Phone Status)
4. Left Display Button (left MENU key)
5. 5553756
6. HangUp Button (Red HandSet key)

CH           Channel Number
RX           Signal Strength (dB)
N             NCC (Color Code)
B              BCC (Color Code)
CI            Cell ID (in Hex)
C1+         how long before phone does forced hand over. (see RX and RXAM)
LAI          Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC
TXPWR   Transmit Power (dB)
RXAM     Reeceive signal strength cut-off point
TS*          Time Slot Number
TA*          Timing Advance. Distance from tower in Km * 2
PL*          Power Level

Power Table
PL:       5 6 7 8 9 10 11 12 13 14 15
dB:       33 31 29 27 25 23 21 19 17 15 13
Watts:   2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02

LF*     C1 value with continuous transmisson from tower
LS*     C1 Value with discontinuous tranmission from tower
QF*     Bit Error Rate with continuous transmission from tower
QS*     Bit Error Rate with discontinuous transmission from tower

BER (bit error rate) table
QF/QS register: 0 1 2 3 4 5 6 7
% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO

SP unlock *#0003*(secret code 8 digits)#

*#0606# shows you Secret Code, but only without SIM Card.

*#06# for checking the IMEI (International Mobile Equipment Identity)

Resets language to automatic selection : * # 0000 # then Green button

SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

Tetris
Power on phone and enter PIN. before phone has locked onto network, F9, send own number, hit right button, hit 9. left is 2, right is 8, rotate is 5, and drop is 4.

Monitor Mode
1. Menu
2. 9 (Phone Options)
3. 7 (Phone Status)
4. Left Display Button (left MENU key)
5. 5553756
6. HangUp Button (Red HandSet key) )

CH           Channel Number
RX           Signal Strength (dB)
N             NCC (Color Code)
B              BCC (Color Code)
CI            Cell ID (in Hex)
C1+         how long before phone does forced hand over. (see RX and RXAM)
LAI          Location Area Identity. Display Network ID code (42F010 = 240.01) and MSC
TXPWR   Transmit Power (dB)
RXAM     Reeceive signal strength cut-off point
TS*          Time Slot Number
TA*          Timing Advance. Distance from tower in Km * 2
PL*          Power Level

Power Table
PL:       5 6 7 8 9 10 11 12 13 14 15
dB:       33 31 29 27 25 23 21 19 17 15 13
Watts:   2 1.3 .8 .5 .3 .2 .13 .08 .05 .03 .02

LF*     C1 value with continuous transmisson from tower
LS*     C1 Value with discontinuous tranmission from tower
QF*     Bit Error Rate with continuous transmission from tower
QS*     Bit Error Rate with discontinuous transmission from tower

BER (bit error rate) table
QF/QS register: 0 1 2 3 4 5 6 7
% of bit sent: 0.2 0.8 0.4 1.6 3.2 6.4 12.8 25.6

Unlock Siemens S3(Not S3 COM)
(For advanced users only)

At addresses 0D8 to 0DD the phones code is stored. To read the code swap nibbles stored at addresses from 0DA to 0DD. Error counter is at 0D9. To clear the Phone Code write at addresses from 0D8 to 0DD: 00, 00, FF, FF, FF, FF.

Show IMEI code: * # 06 #

MONITOR MODE
The Siemens S3 Com series have a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone.

TO ACTIVATE MONITOR MODE
1. Turn the phone on.
2. Enter the PIN access code on press OK. (Only if is enabled).
3. Press Menu. (Left top button).
4. Press 9. (Phone Options).
5. Press 8. (Phone Status) (May be button 7 in some phones).
6. You may see your IMEI Number
7. Left Display Button (Top left MENU key).
8. 7684666
9. HangUp Button. (Red HandSet key).

Note: Monitor should appear now at the bottom of the Network Options menu.

MONITOR MODE TOGGLE
Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO

SP unlock *#0003*(secret code 8 digits)#

*#06# for checking the IMEI (International Mobile Equipment Identity)

MONITOR MODE
The Siemens S4 series also haves a Monitor mode that can be activated directly from the standard user keypad. In order to activate this mode, you must enter the special access code currently programmed into the phone.

TO ACTIVATE MONITOR MODE
1. Menu
2. 9 (Phone Options)
3. 7 (Phone Status)
4. Left Display Button (left MENU key)
5. 7684666
6. HangUp Button (Red HandSet key)

Now "Monitor" should appear at the bottom of the Network Options menu. Pressing the right Display Button when in monitor mode will show a list of the six cells with the strongest signals. Test Mode Indicators: (* = only available when call in progress )

Unlock Siemens S4
(For advanced users only)

At addresses 0D8 to 0DD the phones code is stored. To read the code swap nibbles stored at addresses from 0DA to 0DD. Error counter is at 0D9. To clear the Phone Code write at addresses from 0D8 to 0DD: 00, 00, FF, FF, FF, FF.

Pin Out

1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO